SAMSUNG cleaning maker versions without a display screen signal concerning the same error the following method. Two temperature signs 40 ° C and also Cold will flash concurrently. Besides that, all the cleaning modes indications will blink, also.

The definition of the OE error code Samsung cleaning machines
In Samsung equipments, the OE code suggests a water overflow mistake. The gadget gets a signal from the level sensing unit (stress button). According to that, water is more than essential for the picked program. As a result, the device stops washing and also turns on the drain pump.
The OE mistake means Overflow Mistake. The OF encoding coincides word repetition OverFlow. Although the cause can be both a genuine overflow of water and also inaccurate readings of the level sensor (stress switch). In Samsung washing devices, launched prior to 2007, the error code resembles E3.
Just how to eliminate the OE error code
Create 1– The washer’s owner used excessive washing powder or used an inappropriate cleaning agent
A big amount of powder or the incorrect option (for example, for hand cleaning) is the reason for the formation of abundant foam. It enters into the stress switch tube and creates excess stress. As a result of this, the sensing unit sends out a signal of the high frequency to the control module. The last one begins draining the water. For that reason, the OE code appears on the Samsung washing device display screen.
To eliminate the error of the “false” overflow as a result of the foam, supply the following actions. Switch on the spin mode to totally drain water, get rid of the laundry as well as run the gadget in rinse mode. It will certainly clean out the drum. After that, switch on the washing mode again without laundry and also powder. This way, you can inspect the washing machine’s operating. If the OE code no longer lights up, after that you have effectively gotten rid of the mistake reason.
Cause 2– The maker is full of water from the sewer system through the drainpipe pipe
It is feasible that your Samsung cleaning equipment is not correctly attached to the sewer. For that reason, the water from the siphon sink or drain gets involved in the appliance. If there is a lot of it, the level sensor finds it and displays an overflow mistake code.
To get rid of the source of overflow, attach the drain to the drain correctly. You can do it on your own or look to the expert services of washing makers installing. Then drain the water by running the spin setting and afterwards take out the laundry. For a complete check, run washing with no clothes. With the correct link of the hose to the sewerage, flooding with drains pipes will stop. As a result, the overflow code will certainly no longer pop out.
Cause 3– Control component failure
Electronic “brains” often make errors as well as problem error codes without reason. You can fix the scenario by reactivating the home appliance. Switch off the unit with the power switch as well as unplug the cord. Leave it for five minutes. After that connect it in power as well as start the cleaning once again. If the error is “created” by the control module, the code will certainly not illuminate anymore.
Yet what if the reset, cleaning out the powder and also examining the drain hose connection do not aid? The Samsung cleaning maker constantly releases the OE mistake. So, your method calls for professional evaluating as well as repair by a specialist.
Feasible malfunctions calling for repair service
There are a variety of significant breakdowns, which create the OE code to show up on the screen
| Signs of an error | Possible cause of occurrence | Repair or replacement |
| After turning on the Samsung washing machine:immediately shows the error code of overflow: the OE fault and so on.Or not having completed the water set, the device interrupts washing and activates draining. The display shows the OE fault code. | The water level sensor (pressure switch) is defective. The cause for that is a short circuit or the membrane damage. Therefore, the sensor signals a high water level regardless of its amount in the tank. | Replacing the pressure switch is necessary. |
| There is debris in the tube or the air chamber of the pressure switch. The tube is connected to a high-pressure chamber in the sensor. In this place, a membrane with a tip is fixed to control the relay. If there is dirt in the tube or the chamber, the membrane closes the relay. Then, the sensor gives a signal of overflow even with a small water level. One of the reasons for the contamination is a wrong washing powder causing excess foaming. | “Blow” the tube and the air chamber of the pressure switch. | |
| Samsung washing machine:Blocks the door and does not start washing. The 0E code immediately appears on display.or starts water draining at the same time as gaining. The appliance issues the OE overflow error code. | The electronic controller (control board) is out of order. The cause of the failure may be damage to tracks on the board, a burnt out resistor (fuse) or a breakdown (short circuit) of the microcircuits. | Solder the damaged tracks to restore contact. Replace the fuse with a new one.You can not repair a broken chip. Only the complete replacing of the controller will solve the problem. |
| Samsung washing machine gains a full tank of water for 1-2 minutes after starting any washing program. Then, an overflow error appears on display. | Damage to the water inlet valve. A defective valve does not shut off the water after the stop signal.Attention! In this situation, do not wait for the overflow error code to appear! You risk flooding the bathroom or kitchen with water. Turn off the machine and de-energize it. Also, turn off the water tap. | Replace the water valve. |
| After starting the washing, the appliance doesn’t gain water. After a few seconds, an overflow error occurs, and the Samsung washing machine shuts down. | There is a breakage in the circuit of the water level sensor (weak contact, wire break). The control module receives incorrect information about the overflow. It happens because of a wire break in the pressure switch circuit or burnt out contacts. Rodents often spoil wiring in devices, especially in private cottages and cottages. | You need to make a twist to connect the damaged wiring or put a new cable. Clean and, if necessary, solder the contacts. |