For the first time, faults with the 1E code can appear at any kind of phase of cleaning. When a customer reboots the washer, the fault signals show up promptly after the beginning. It takes place even prior to water acquiring. The 1E mistake suggests a trouble with the water level sensor (a stress switch). In most cases, this implies that the individual requires to change the part.
There are also “incorrect” alarms when the customer can get rid of faults without the aid of an expert.
In washers without a screen, the 1E code represents:
blinking of all light indicators;
brightening of the temperature mode signs of 40 as well as 60 levels;
a light bulb of the “cold” washing setting brighten.
The E7 error code in Samsung washer was utilized till 2007. In late items, the very same trouble describes the 1E error code. In some washing machines, a similar trouble codes as the 1C mistake. These mistakes are totally similar to every other. Additionally, the same set of problems cause them.
The control module failing: what to do
To inspect this alternative, disconnect the devices from the network for a few mins. After that, reconnect it. If the cause remains in the controller procedure failing of the cleaning maker, after a forced reset, the mistake signal vanishes.
The pressure button tube is separated from the machine or curved
Check the hose connecting the pressure tasting chamber to the sensor. The last one identifies the water degree. During washing machine operating, the tube might be curved or different from the adapter. In this instance, the relay can not appropriately measure the volume of water poured into the tank. In this case, the display shows the 1E mistake.
Correct the alignment of or reconnect the pipe. This action will bring back the normal operation of the Samsung washing device.
If after examining the issue the device still reveals the mistake, most likely the hardware is damaged.
How to get rid of the 1E mistake code in Samsung washing machine
The failure of some components most often causes 1E mistakes. The table will certainly help you to determine how to deal with the breakdown.
| Malfunction | Possible cases | What to do |
| The machine does not gain water, the 1E error appears. | The hose is clogged, incorrectly connected or mechanically damaged. The relay damage. | Check the tightness of the drain hose connected to the output of the washer. Eliminate bendings. Make sure that the hose is intact.Replace the damaged hose or relay (ask a specialist for help). |
| Error codes appear on the display right after the start of the technique operation. | The electronic control module malfunction in the washing machine. | For an accurate diagnosis, you need the expert’s assistance. If the resistor is burnt out in the module, it is enough to resolder.If a problem occurs in the washing machine processor, you have to completely replace the unit. |
| The technique issues the errors in a short time after the start of washing. | The sensor contacts oxidization. The integrity of the wiring of the pressure switch or the electronic unit breakage. | It is necessary to adjust the current supply by clearing the contacts. Also, re-twist the wires and replace the tail. |
No contact with the stress switch or electronic component.
Occasionally the relay does not run properly when it involves insufficient call with the device electronics. This part figures out the level of water. If there is a failure, the 1E mistake occurs. Inspect whether the digital blocks of the washing machine are securely affixed.
It is much easier to reach the pressure button than to the heating element or control component in the Samsung washing equipment.
Shut off the water, separate the washing pipe of the strategy.
Separate the drainpipe tube from the sewerage lines.
Separate the home appliance from the keys.
Take out the powder tray.
Eliminate 2 screws. They are located on the back wall surface in the upper right as well as left edges of the instance.
Get rid of the top cover of the washing equipment.
You can discover the pressure button at the top of the machine body. Look closer to the back wall. It is difficult to confuse this aspect with a few other information.
Get rid of the top cover of the washing equipment.
You can discover the pressure button at the top of the machine body. Look closer to the back wall. It is difficult to confuse this aspect with a few other information.
Where is the stress button Samsung washing machine.
Having actually located the stress button, examine the stress tube to wear out and clog. If you can’t locate any type of failures, use the multimeter. Begin evaluating the resistance and the contacts of the water degree sensor.
Having inspected the water degree sensing unit, test the electrical interactions. It feeds and also attaches the part to the control module. Likewise, inspect a loophole on the whole information and each cord individually. If the circuitry is in order, we are most likely dealing with a serious mistake in the control module.
Charred out tracks of the control panel, triacs, as well as other semiconductor aspects can affect the typical interaction with the stress button. You can try to inspect a loop on them. Possibly, you will certainly have the ability to locate the faulty component. But more than likely, looking for an issue as well as its removal will be rather hard.
We constantly advise handing over faults in the electronic devices of a washing device to a specialist. Find a specialist who will deal with the failure at no added price.
Finally, we need to note that the stress button can make a great deal of surprises. Although, it is among the most easy-to-repair components of a cleaning machine. So, if you face the 1E error in Samsung cleaning equipment, be incredibly cautious.