Bosch Nexxt 500 series washer shows the E02 mistake code. It indicates about issues with the electric motor of the device. In this case, the drum does not rotate when the washing program is run, or the program does not start whatsoever.

What should a regular user do and exactly how to repair the scenario? You can call the specialist, or you can attempt to repair the issue on your own.
The E02 error code in the Bosch Nexxt 500 series washer, revealed on the screen, is critical. If you don’t remove it, the electrical wiring or the engine of the Bosch washer might catch fire.
What does the E02 in Bosch Nexxt 500 series washer mean: options for removing
You can try to solve the trouble without disassembling the system of the washing machine. To do this, continue as follows:
Examine if the keys voltage is enough for the operation of the Bosch Nexxt 500 series washing machine. If not, you may require the help of an electrical expert.
Disconnect the device from the keys for 15-20 mins. If after reboot the E02 error is reset, after that the reason remained in the failure of the electronic controller.
If the referrals did not help to eliminate the mistake, look for a failure as well as fix the part.
Causes for breakage as well as fixing
The electric motor is an integral part of a washing machine. The component is accountable for the drum turnings throughout cleaning. So if you do not fix the issue, most importantly it will be difficult to use the Bosch Nexxt 500 series washing machine.
Nonetheless, the cause of the failure does not cover in the engine.
Brushes are worn out
80% of the break downs appearing with the E02 mistake in the Bosch Nexxt 500 collection washing machine drops on the carbon brushes of the electrical motor.
In time, these parts wear out. And also therefore, the motor quits. These indications can mention that brushes are out of order:
A washing machine, as always, gets as well as drains pipes the water, but the drum does not spin.
An individual hears some sound as well as notices the sparks under the Bosch washing machine.
Exactly how to fix if the E02 error is brightened:
Disconnect the washer from the keys.
Disassemble the Bosch Nexxt 500 series washing machine.
The engine lies below, under the drum.
Remove the transmission belt as well as disconnect the electric motor cords.
Loosen up the screws that protect the electric motor.
Eliminate the engine and wring out the carbon brush get in touches with.
Get rid of the brushes. Inspect: if the parts are almost or entirely used, change it.
Rotor bearing failure
If you listen to some sound throughout rotating or notice a leakage in the container, take care. The factor for it is the water that has gotten involved in the bearing of the rotor.
What must I do to resolve the problem as well as reset the error:
Mount the brand-new electric motor in the Bosch Nexxt 500 collection washer.
Get rid of the motor and get the blades. Get rid of the protective cover from the bearings. After cleansing and handling, oil the bearing.
Totally replace the bearing. Deformation of the blades axis is quite a common trouble. In this case, the user can hear rolling sounds when the motor rotates.
Replace the blades with a new one.
Tacho sensor is out of order
Tacho sensing unit (Hall sensor) regulates the rate of the drum turning.
These indications show a breakdown of a tachogenerator. The drum revolves extraordinarily rapidly, then stops, and also creates an E02 error.
If you see such “behavior” of the Bosch washing machine, then you require to check the sensing unit with a multimeter. The resistance of 70 ohms is regular. In this instance, the tool is working effectively. If the device is broken, change it.
The last point to examine is the engine. The multimeter tester will certainly help you with this. The gadget’s performance should be from 1 to 7 ohms.
Very seldom, the error code is presented as a result of a fault in the control component. However, if you exclude all various other breakdowns, examine the component.
It may be essential to change the device or repair the board. Prior to removing the problem, consider whether you can deal with the repair on your own or otherwise!